Mikrostruktur dan Karakterisasi Sifat Mekanik Lapisan Cr3C2-NiAl-Al2O3 Hasil Deposisi Dengan Menggunakan High Velocity Oxygen Fuel Thermal Spray Coating

Edy Riyanto; Budi Prawara; Edy Riyanto; Budi Prawara

doi:10.14203/j.mev.2010.v1.1-4

Mikrostruktur dan Karakterisasi Sifat Mekanik Lapisan Cr3C2-NiAl-Al2O3 Hasil Deposisi Dengan Menggunakan High Velocity Oxygen Fuel Thermal Spray Coating

Edy Riyanto, Budi Prawara

Abstract

Surface coating processing of industrial component with thermal spray coatings have been applied in many industrial fields. Ceramic matrix composite coating which consists of Cr₃C₂-Al₂O₃-NiAl had been carried out to obtain layers of material that has superior mechanical properties to enhance component performance. Deposition of CMC with High Velocity Oxygen Fuel (HVOF) thermal spray coating has been employed. This study aims to determine the effect of powder particle size on the microstructure, surface roughness and hardness of the layer, by varying the NiAl powder particle size. Test results show NiAl powder particle size has an influence on the mechanical properties of CMC coating. Hardness of coating increases and surface roughness values of coating decrease with smaller NiAl particle size.

10.14203/j.mev.2010.v1.1-4

Keywords

Thermal Spray Coating; High Velocity Oxygen Fuel; Cr3C2-NiAl-Al2O3 Coating

Full Text:

PDF

References

M. Magnani, P.H. Soegama, N. Espallargas, C.S. Fugivara, S. Dosta, J.M. Guilemany, and A.V. Benedetti, Corrosion and Wear Studies of Cr3C2-NiCr-HVOF Coatings Sprayed on AA7050 T7 Under Cooling, Journal of Thermal Spray Technology, March 2009. crossreff

J. He, M. Ice and E. Lavernia, Particle Melting Behaviour During High Velocity Oxygen Fuel Thermal Spraying, Journal of Thermal Spray Technology, Vol 10(1), 2001, pp. 83-93.

E. Turunen, Diagnostic Tools for HVOF Process Optimization, Dissertation for the degree doctor of Science, Helsinki University of Technology, Espoo, Finland, 2005.

K.W. David Hart, D.H. Harper, M.J. Gill and G.R. Heath, Case Studies in Wear Resistance Using HVOF, PTAW and Spray Fusion Surfacing, Eutectectic Canada Inc., Edmonton, Alberta, Canada.

D.E. Wolfe, T.J. Eden, J.K. Potter and A.P. Jaroh, Investigation and Characterization of Cr3C2 – Based Wear-Resistant Coatings Applied by the Cold Spray Process, Journal of Thermal Spray Technology, Vol 15(3), 2006, pp. 400- 412.

G.-J. Ji, C.-J. Li, Y.-Y. Wang and W.-Y. Li, Erotion Performance of HVOF-Sprayed Cr3C2-NiCr Coatings, Journal of Thermal Spray Technology, Vol 16(4), 2007, pp. 557-565.

C.-J. Li, Y.-Y. Wang, Effect of Particle State on the Adhesive Strength of HVOF Sprayed Metallic Coating, Journal of Thermal Spray Technology, Vol 11(4), 2002, pp. 523- 529.

V.V.Sobolev, J.M.Guilemany, and A.J.Martin, Flattening of Composite Powder Particles during Thermal Spraying, Journal of Thermal Spray Technology, Vol 6(3), 1997, pp. 353- 360.

R.S.Neiser, M.F.Smith, and R.C.Dykhuizen, Oxidation in Wire HVOFSprayed Steel, Journal of Thermal Spray Technology, Vol 7(4), 1998, pp. 537-545.