Modeling and design of cooperative braking in electric and hybrid vehicles using induction machine and hydraulic brake

Zaini Dalimus, Khallid Hussain, Andrew J. Day


In mixed-mode braking applications, the electric motor / generator (M/G) and hydraulic pressure valve are controlled to meet the driver’s braking demand. Controlling these braking elements is achieved by modulating the current generated by the M/G and adjusting the fluid pressure to the wheel brake cylinders. This paper aims to model and design combined regenerative and hydraulic braking systems which, comprise an induction electric machine, inverter, NiMH battery, controller, a pressure source, pressure control unit, and brake calipers. A 15 kW 1500 rpm induction machine equipped with a reduction gear having a gear ratio of 4 is used. A hydraulic brake capable to produce fluid pressure up to 40 bar is used. Direct torque control and pressure control are chosen as the control criteria in the M/G and the hydraulic solenoid valve. The braking demands for the system are derived from the Federal Testing Procedure (FTP) drive cycle. Two simulation models have been developed in Matlab®/Simulink® to analyze the performance of the control strategy in each braking system. The developed model is validated through experiment. It is concluded that the control system does introduce torque ripple and pressure oscillation in the braking system, but these effects do not affect vehicle braking performance due to the high frequency nature of pressure fluctuation and the damping effect of the vehicle inertia. Moreover, experiment results prove the effectiveness of the developed model.

Full Text:



Zaini Dalimus, “Braking System Modeling and Brake Temperature Response to Repeated Cycle,” Journal of Mechatronics, Electrical Power, and Vehicular Technology, 2014, vol. 05, pp.123-128. Crossref

Chau, K. T., Chan, C. C., Liu, C.: “Overview of permanent-magnet brushless drives for electric and hybrid electric vehicles,” IEEE Transactions on Industrial Electronics, 2008, 55, (6), pp. 2246-2257. Crossref

Dorrell, D.G., Knight, A.M.,Popescu, M., Evans, L., Staton, D.A.: “Comparison of different motor design drives for hybrid electric vehicles,” Energy Conversion Congress and Exposition, 2010, pp. 3352 – 3359. Crossref

Khoucha, F., Marouani, K., Haddoun, A., Kheloui, A. and Benbouzid, M.E.H. : “Improved Sensorless DTC Scheme for EV Induction Motors,” 2007 IEEE International Electric Machines & Drives Conference, Antalya, 2007, pp. 1159-1164. Crossref

Vyncke, T. J., Boel R. K.,Melkebeek, J. A. A.: “Direct torque control of permanent magnet synchronous motors – an overview,”

rd IEEE Benelux Young Researchers Symposium in Electrical Power Engineering, Ghent, Belgium, 2006, pp. 1-5. Crossref

Ohtani, Y., Innami, T., Obata, T., Yamaguchi, T., Kimura, T. and Oshima, T.: “Development of an Electrically-Driven Intelligent Brake Unit,” SAE Techical Paper, 2011-01-0572. 2007. Crossref

Yuan, D., Wei, J., Qu, Y., and Wu, J. : “Simulation of hydraulic brake built-in test system for a certain UAV,” Control Conference (CCC), 2013 32nd Chinese, Xi'an, 2013, pp. 801-804.

Park, M., Kim, S.,Yang, L., Kim, K.: “Development of the control logic of electronically controlled hydraulic brake system for hybrid vehicle,” SAE Technical Paper 2009-01-1215, 2009, pp. 1-7. Crossref

Aoki, Y., Suzuki, K., Nakano, H., Akamine, K.: “Development of hydraulic servo brake systemfor cooperative control with regenerative brake,” SAE Technical Paper 2007-01-0868, 2007, pp. 1-9. Crossref

Albrichsfeld, C. V., Karner, J.: “Brake system for hybrid and electric vehicles,” SAE Technical Paper 2009-01-1217, 2009, pp. 1-7. Crossref

Lei, Z., Yugong, L., Diange, Y., Keqiang, L., and Xiaomin, L., “A novel brake control strategy for electric vehicles based on slip trial method,” Vehicular Electronics and Safety, 2007. ICVES. IEEE International Conference on, Beijing, 2007, pp. 1-6. Crossref

Tremblay, O., Dessaint, L. A.: “Experimental validation of a battery dynamic model for EV applications,” World Electric Vehicle Journal, 2009, 3, pp. 1-10

Ghorbani, M. J., Akhbari, M. and Mokhtari, H. : “Direct torque control of induction motor by Active Learning Method,” Power Electronic & Drive Systems & Technologies Conference (PEDSTC), 2010 1st, Tehran, Iran, 2010, pp. 267-272. Crossref

Qi, X., Song, J., Wang, H.: “Influence of hydraulic ABS parameters on solenoid valve dynamic response and braking effect,” SAE Technical Paper 2005-01-1590, 2005, pp. 1-12. Crossref

Zaini, Z., Hussain, K., Day, A. J.: “Mixed-mode braking system for road vehicles with regenerative braking,” 6th European Conference on Braking, Lille, France, 2010, pp. 115-122.

Article Metrics

Metrics Loading ...

Metrics powered by PLOS ALM


  • There are currently no refbacks.

Copyright (c) 2016 Journal of Mechatronics, Electrical Power, and Vehicular Technology

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.



1. Braking control strategies of modern hybrid and electric vehicles
Z Zaini
Journal of Physics: Conference Series  vol: 1469  issue: 1  first page: 012173  year: 2020  
doi: 10.1088/1742-6596/1469/1/012173