Analytical optimization of displacer trajectory for ideal  beta-type stirling engine cycles with sinusoidal piston motion

Rachman Hakim; Toto Hardianto; Priyono Sutikno; Poetro Sambegoro; Rachman Hakim; Toto Hardianto; Priyono Sutikno; Poetro Sambegoro

doi:10.55981/j.mev.2026.1486

Analytical optimization of displacer trajectory for ideal beta-type stirling engine cycles with sinusoidal piston motion

Rachman Hakim, Toto Hardianto, Priyono Sutikno, Poetro Sambegoro

Abstract

This study develops a generalized displacer motion equation for a beta-type Stirling engine. The proposed equation approximates the ideal Stirling cycle while maintaining sinusoidal piston motion to ensure stable power extraction. The displacer trajectory is modeled with a Fourier series and optimized. The resulting trajectory is then generalized as a piecewise function to improve applicability across different geometries. This approach improves control of working fluid distribution, allowing the expansion and compression processes to more closely approach isothermal conditions. The results show that the optimized Fourier trajectory achieves 91.9 % of the ideal Stirling-cycle work output, outperforming conventional drive mechanisms, where it only achieves 59.8 % for crank mechanism, 66 % for Scotch yoke, and 68.5 % for rhombic drive. For practical implementation, the optimized Fourier trajectory is generalized using a piecewise formulation. The generalized trajectory maintains approximately 80–90 % of the ideal Stirling-cycle work over a range of compression ratios without requiring re-optimization. These results demonstrate that the proposed approach provides both high thermodynamic performance and improved adaptability compared with conventional Stirling engine drive mechanisms.

10.55981/j.mev.2026.1486

Keywords

displacer control; displacer trajectory; Fourier trajectory; piecewise function; Stirling engine.

Full Text:

PDF

References

D. Roy et al., “Techno-economic and environmental analyses of a solar-assisted Stirling engine cogeneration system for different dwelling types in the United Kingdom,” Energy Convers. Manag., vol. 302, Feb. 2024.

K. Laazaar and N. Boutammachte, “New approach of decision support method for Stirling engine type choice towards a better exploitation of renewable energies,” Energy Convers. Manag., vol. 223, Nov. 2020.

A. C. Ferreira, J. Silva, S. Teixeira, J. C. Teixeira, and S. A. Nebra, “Assessment of the Stirling engine performance comparing two renewable energy sources: Solar energy and biomass,” Renewable Energy, vol. 154, pp. 581–597, 2020, doi: https://doi.org/10.1016/j.renene.2020.03.020.

R. Pido, S. Humena, and F. Abdullah, “Performance study of corncob-fueled updraft gasification with integrated solar power plant as a supporting energy source for the reactor,” Journal of Mechatronics, Electrical Power, and Vehicular Technology, vol. 16, no. 2, Dec. 2025.

S. S. Jaafar, H. A. Maarof, H. B. Hamasalh, and K. M. Ahmed, “Comparative performance evaluation of dual-axis solar trackers: Enhancing solar harvesting efficiency,” Journal of Mechatronics, Electrical Power, and Vehicular Technology, vol. 15, no. 1, pp. 23–31, 2024.

K. Wang, S. R. Sanders, S. Dubey, F. H. Choo, and F. Duan, “Stirling cycle engines for recovering low and moderate temperature heat: A review,” Renewable and Sustainable Energy Reviews, vol. 62, pp. 89–108, 2016.

S. Zare, A. R. Tavakolpour-saleh, A. Aghahosseini, M. H. Sangdani, and R. Mirshekari, “Design and optimization of Stirling engines using soft computing methods: A review,” Appl. Energy, vol. 283, Feb. 2021.

F. Xin, B. Xu, D. Dai, W. Liu, and Z. Liu, “Evaluation of heat transfer enhancement effect at the hot/cold end of a Stirling engine using performance improvement factor,” Energy, vol. 311, Dec. 2024.

F. Aksoy et al., “Effects of the regenerator on engine performance of a rhombic drive beta type stirling engine,” Energy Sources, Part A: Recovery, Utilization and Environmental Effects, vol. 47, no. 1, pp. 6665–6673, 2025.

D. Erol, “An experimental comparative study of the effects on the engine performance of using three different motion mechanisms in a beta-configuration Stirling engine,” Energy, vol. 293, p. 130660, 2024.

H.-S. Yang, H.-Q. Zhu, and X.-Z. Xiao, “Comparison of the dynamic characteristics and performance of beta-type Stirling engines operating with different driving mechanisms,” Energy, vol. 275, p. 127535, 2023.

A. Hadidi, “Enhanced design of Stirling engines via multi-objective optimization: Effects of dead volumes, regenerator effectiveness, and operating parameters,” Case Studies in Thermal Engineering, vol. 77, p. 107582, Jan. 2026.

T. Ergin, “Experimental optimization of displacer working gap in a gamma-type Stirling engine,” Engineering Science and Technology, an International Journal, vol. 52, Apr. 2024.

D. Erol, H. Yaman, and B. Doğan, “A review development of rhombic drive mechanism used in the Stirling engines,” Elsevier Ltd., vol. 78, 2017, p. 1044-1067.

J. Podešva and Z. Poruba, “The Stirling engine mechanism optimization,” Perspect. Sci. (Neth)., vol. 7, pp. 341–346, Mar. 2016.

H. Bi, J. Yang, C. Chen, and B. Luo, “Heat transfer and flow characteristics of intermittent oscillating flow in tube,” Appl. Therm. Eng., vol. 225, May 2023.

M. Nicol-Set and D. Nobes, “Experimental evaluation of piston motion modification to improve the thermodynamic power output of a low temperature gamma Stirling engine,” in E3S Web of Conferences, EDP Sciences, Oct. 2021.

S. Ranieri, G. A. O. Prado, and B. D. MacDonald, “Efficiency reduction in stirling engines resulting from sinusoidal motion,” Energies (Basel)., vol. 11, no. 11, Nov. 2018.

M. Farid Zainudin, R. Abu Bakar, K. Al Kadirgama, and G. Leong Ming, “Kinematic and thermodynamic operational analysis of rhombic-drive Stirling engine prototype,” in IOP Conference Series: Materials Science and Engineering, vol. 788, Jun. 2020.

M. Craun and B. Bamieh, “Optimal periodic control of an ideal stirling engine model,” Journal of Dynamic Systems, Measurement and Control, Transactions of the ASME, vol. 137, no. 7, Jul. 2015.

H. Tian, S. Zhao, S. Kuang, and Y. Gong, “Enhanced thermodynamic performance of a modified α type Stirling engine with fine-tuned piston trajectories controlled via staircase decomposed target signals,” Case Studies in Thermal Engineering, vol. 73, p. 106512, Sep. 2025.

E. Öztürk, “Optimization of a novel drive mechanism approaching the ideal cycle for beta type Stirling engines,” Engineering Science and Technology, an International Journal, vol. 47, p. 101555, Nov. 2023.

H. M. Wong and S. Y. Goh, “Experimental comparison of sinusoidal motion and non-sinusoidal motion of rise-dwell-fall-dwell in a Stirling engine,” Journal of Mechanical Engineering and Sciences, vol. 14, no. 3, pp. 6971–6981, Sep. 2020.

H. M. Wong, R. Bahar, and Y. S. Ong, “Experimental evaluation of the displacer and working piston hybrid motion to improve the performance of a stirling engine,” Appl. Therm. Eng., vol. 279, Nov. 2025.

W. Ye, T. Zhang, X. Wang, Y. Liu, and P. Chen, “Parametric study of gamma-type free piston stirling engine using nonlinear thermodynamic-dynamic coupled model,” Energy, vol. 211, Nov. 2020.

R. Sharma and B. Glemmestad, “On generalized reduced gradient method with multi-start and self-optimizing control structure for gas lift allocation optimization,” J. Process Control, vol. 23, no. 8, pp. 1129–1140, 2013.

H. Hachem, R. Gheith, F. Aloui, and S. Ben Nasrallah, “Technological challenges and optimization efforts of the Stirling machine: A review,” Energy Conversion and Management., vol. 171, pp. 1365-1387, 2018.

S. A. Salih, B. A. Aljashaami, N. T. Alwan, M. A. Qasim, S. E. Shcheklein, and V. I. Velkin, “Isothermal thermodynamic analysis investigation of the Stirling engine types (alpha, beta, gamma): A theatrical study,” Mater. Today Proc., 2023.